1 files changed, 13 insertions, 12 deletions

diff --git a/examples/Single_Shot_Conv_Ready_Controlled/Single_Shot_Conv_Ready_Controlled.ino b/examples/Single_Shot_Conv_Ready_Controlled/Single_Shot_Conv_Ready_Controlled.ino
index 9ca409e..f1c2696 100644
--- a/examples/Single_Shot_Conv_Ready_Controlled/Single_Shot_Conv_Ready_Controlled.ino
+++ b/examples/Single_Shot_Conv_Ready_Controlled/Single_Shot_Conv_Ready_Controlled.ino
@@ -5,7 +5,8 @@
 * This does not work in the continuous mode. 

 *  

 * Further information can be found on:

-* https://wolles-elektronikkiste.de/ads1115

+* https://wolles-elektronikkiste.de/ads1115 (German)

+* https://wolles-elektronikkiste.de/en/ads1115-a-d-converter-with-amplifier (English)

 * 

 ***************************************************************************/

 

@@ -48,7 +49,7 @@ void setup() {
    */

   adc.setCompareChannels(ADS1115_COMP_0_GND); //comment line/change parameter to change channels

 

-  /* Set number of conversions after which the alert pin will be active

+  /* Set number of conversions after which the alert pin will assert

    * - or you can disable the alert 

    *  

    *  ADS1115_ASSERT_AFTER_1  -> after 1 conversion

@@ -79,10 +80,10 @@ void setup() {
    */

   //adc.setMeasureMode(ADS1115_CONTINUOUS); //continuous mode does not work with conversion ready (isBusy)

 

-   /* Choose maximum limit or maximum and minimum alert limit (window)in Volt - alert pin will 

-   *  be active when measured values are beyond the maximum limit or outside the window 

+   /* Choose maximum limit or maximum and minimum alert limit (window) in volts - alert pin will 

+   *  assert when measured values are beyond the maximum limit or outside the window 

    *  Upper limit first: setAlertLimit_V(MODE, maximum, minimum)

-   *  In max limit mode the minimum value is the limit where the alert pin will be deactivated (if 

+   *  In max limit mode the minimum value is the limit where the alert pin assertion will be cleared (if 

    *  not latched)  

    * 

    *  ADS1115_MAX_LIMIT

@@ -91,9 +92,9 @@ void setup() {
    */

   //adc.setAlertModeAndLimit_V(ADS1115_MAX_LIMIT, 3.0, 1.5); //uncomment if you want to change the default

   

-  /* Enable or disable latch. If latch is enabled the alarm pin will be active until the

-   * conversion register is read (getResult functions). If disabled the alarm pin will be

-   * deactivated with next value within limits. 

+  /* Enable or disable latch. If latch is enabled the alert pin will assert until the

+   * conversion register is read (getResult functions). If disabled the alert pin assertion will be

+   * cleared with next value within limits. 

    *  

    *  ADS1115_LATCH_DISABLED (default)

    *  ADS1115_LATCH_ENABLED

@@ -102,16 +103,16 @@ void setup() {
 

   /* Sets the alert pin polarity if active:

    *  

-   * Enable or disable latch. If latch is enabled the alarm pin will be active until the

-   * conversion register is read (getResult functions). If disabled the alarm pin will be

-   * deactivated with next value within limits. 

+   * Enable or disable latch. If latch is enabled the alert pin will assert until the

+   * conversion register is read (getResult functions). If disabled the alarm pin assertion

+   * will be cleared with next value within limits. 

    *  

    * ADS1115_ACT_LOW  ->  active low (default)   

    * ADS1115_ACT_HIGH ->  active high

    */

   //adc.setAlertPol(ADS1115_ACT_LOW); //uncomment if you want to change the default

  

-  /* With this function the alert pin will be active, when a conversion is ready.

+  /* With this function the alert pin will assert, when a conversion is ready.

    * In order to deactivate, use the setAlertLimit_V function  

    */

   //adc.setAlertPinToConversionReady(); //uncomment if you want to change the default