#ifndef UTIL_LINUX_PT_BSD_H
#define UTIL_LINUX_PT_BSD_H
#define BSD_MAXPARTITIONS 16
#define BSD_FS_UNUSED 0
#ifndef BSD_DISKMAGIC
# define BSD_DISKMAGIC ((uint32_t) 0x82564557)
#endif
#define BSD_LINUX_BOOTDIR "/usr/ucb/mdec"
#if defined (__alpha__) || defined (__powerpc__) || \
defined (__ia64__) || defined (__hppa__)
# define BSD_LABELSECTOR 0
# define BSD_LABELOFFSET 64
#else
# define BSD_LABELSECTOR 1
# define BSD_LABELOFFSET 0
#endif
#define BSD_BBSIZE 8192 /* size of boot area, with label */
#define BSD_SBSIZE 8192 /* max size of fs superblock */
struct bsd_disklabel {
uint32_t d_magic; /* the magic number */
int16_t d_type; /* drive type */
int16_t d_subtype; /* controller/d_type specific */
char d_typename[16]; /* type name, e.g. "eagle" */
char d_packname[16]; /* pack identifier */
/* disk geometry: */
uint32_t d_secsize; /* # of bytes per sector */
uint32_t d_nsectors; /* # of data sectors per track */
uint32_t d_ntracks; /* # of tracks per cylinder */
uint32_t d_ncylinders; /* # of data cylinders per unit */
uint32_t d_secpercyl; /* # of data sectors per cylinder */
uint32_t d_secperunit; /* # of data sectors per unit */
/*
* Spares (bad sector replacements) below
* are not counted in d_nsectors or d_secpercyl.
* Spare sectors are assumed to be physical sectors
* which occupy space at the end of each track and/or cylinder.
*/
uint16_t d_sparespertrack; /* # of spare sectors per track */
uint16_t d_sparespercyl; /* # of spare sectors per cylinder */
/*
* Alternate cylinders include maintenance, replacement,
* configuration description areas, etc.
*/
uint32_t d_acylinders; /* # of alt. cylinders per unit */
/* hardware characteristics: */
/*
* d_interleave, d_trackskew and d_cylskew describe perturbations
* in the media format used to compensate for a slow controller.
* Interleave is physical sector interleave, set up by the formatter
* or controller when formatting. When interleaving is in use,
* logically adjacent sectors are not physically contiguous,
* but instead are separated by some number of sectors.
* It is specified as the ratio of physical sectors traversed
* per logical sector. Thus an interleave of 1:1 implies contiguous
* layout, while 2:1 implies that logical sector 0 is separated
* by one sector from logical sector 1.
* d_trackskew is the offset of sector 0 on track N
* relative to sector 0 on track N-1 on the same cylinder.
* Finally, d_cylskew is the offset of sector 0 on cylinder N
* relative to sector 0 on cylinder N-1.
*/
uint16_t d_rpm; /* rotational speed */
uint16_t d_interleave; /* hardware sector interleave */
uint16_t d_trackskew; /* sector 0 skew, per track */
uint16_t d_cylskew; /* sector 0 skew, per cylinder */
uint32_t d_headswitch; /* head switch time, usec */
uint32_t d_trkseek; /* track-to-track seek, usec */
uint32_t d_flags; /* generic flags */
uint32_t d_drivedata[5]; /* drive-type specific information */
uint32_t d_spare[5]; /* reserved for future use */
uint32_t d_magic2; /* the magic number (again) */
uint16_t d_checksum; /* xor of data incl. partitions */
/* filesystem and partition information: */
uint16_t d_npartitions; /* number of partitions in following */
uint32_t d_bbsize; /* size of boot area at sn0, bytes */
uint32_t d_sbsize; /* max size of fs superblock, bytes */
struct bsd_partition { /* the partition table */
uint32_t p_size; /* number of sectors in partition */
uint32_t p_offset; /* starting sector */
uint32_t p_fsize; /* filesystem basic fragment size */
uint8_t p_fstype; /* filesystem type, see below */
uint8_t p_frag; /* filesystem fragments per block */
uint16_t p_cpg; /* filesystem cylinders per group */
} __attribute__((packed)) d_partitions[BSD_MAXPARTITIONS]; /* actually may be more */
} __attribute__((packed));
/* d_type values: */
#define BSD_DTYPE_SMD 1 /* SMD, XSMD; VAX hp/up */
#define BSD_DTYPE_MSCP 2 /* MSCP */
#define BSD_DTYPE_DEC 3 /* other DEC (rk, rl) */
#define BSD_DTYPE_SCSI 4 /* SCSI */
#define BSD_DTYPE_ESDI 5 /* ESDI interface */
#define BSD_DTYPE_ST506 6 /* ST506 etc. */
#define BSD_DTYPE_HPIB 7 /* CS/80 on HP-IB */
#define BSD_DTYPE_HPFL 8 /* HP Fiber-link */
#define BSD_DTYPE_FLOPPY 10 /* floppy */
/* d_subtype values: */
#define BSD_DSTYPE_INDOSPART 0x8 /* is inside dos partition */
#define BSD_DSTYPE_DOSPART(s) ((s) & 3) /* dos partition number */
#define BSD_DSTYPE_GEOMETRY 0x10 /* drive params in label */
/*
* Filesystem type and version.
* Used to interpret other filesystem-specific
* per-partition information.
*/
#define BSD_FS_UNUSED 0 /* unused */
#define BSD_FS_SWAP 1 /* swap */
#define BSD_FS_V6 2 /* Sixth Edition */
#define BSD_FS_V7 3 /* Seventh Edition */
#define BSD_FS_SYSV 4 /* System V */
#define BSD_FS_V71K 5 /* V7 with 1K blocks (4.1, 2.9) */
#define BSD_FS_V8 6 /* Eighth Edition, 4K blocks */
#define BSD_FS_BSDFFS 7 /* 4.2BSD fast file system */
#define BSD_FS_BSDLFS 9 /* 4.4BSD log-structured file system */
#define BSD_FS_OTHER 10 /* in use, but unknown/unsupported */
#define BSD_FS_HPFS 11 /* OS/2 high-performance file system */
#define BSD_FS_ISO9660 12 /* ISO-9660 filesystem (cdrom) */
#define BSD_FS_ISOFS BSD_FS_ISO9660
#define BSD_FS_BOOT 13 /* partition contains bootstrap */
#define BSD_FS_ADOS 14 /* AmigaDOS fast file system */
#define BSD_FS_HFS 15 /* Macintosh HFS */
#define BSD_FS_ADVFS 16 /* Digital Unix AdvFS */
/* this is annoying, but it's also the way it is :-( */
#ifdef __alpha__
#define BSD_FS_EXT2 8 /* ext2 file system */
#else
#define BSD_FS_MSDOS 8 /* MS-DOS file system */
#endif
/*
* flags shared by various drives:
*/
#define BSD_D_REMOVABLE 0x01 /* removable media */
#define BSD_D_ECC 0x02 /* supports ECC */
#define BSD_D_BADSECT 0x04 /* supports bad sector forw. */
#define BSD_D_RAMDISK 0x08 /* disk emulator */
#define BSD_D_CHAIN 0x10 /* can do back-back transfers */
#define BSD_D_DOSPART 0x20 /* within MSDOS partition */
#endif /* UTIL_LINUX_PT_BSD_H */
