diff options
Diffstat (limited to '')
| -rw-r--r-- | .travis.yml | 2 | ||||
| -rw-r--r-- | examples/Continuous/Continuous.ino (renamed from examples/Continous/Continous.ino) | 258 |
2 files changed, 130 insertions, 130 deletions
diff --git a/.travis.yml b/.travis.yml index aa1001a..21a9ca6 100644 --- a/.travis.yml +++ b/.travis.yml @@ -32,7 +32,7 @@ cache: env: - PLATFORMIO_CI_SRC=examples/Single_Shot/Single_Shot.ino - - PLATFORMIO_CI_SRC=examples/Continous/Continous.ino + - PLATFORMIO_CI_SRC=examples/Continuous/Continuous.ino - PLATFORMIO_CI_SRC=examples/Alert_Window_Mode/Alert_Window_Mode.ino install: diff --git a/examples/Continous/Continous.ino b/examples/Continuous/Continuous.ino index bece321..3c8313a 100644 --- a/examples/Continous/Continous.ino +++ b/examples/Continuous/Continuous.ino @@ -1,129 +1,129 @@ -/***************************************************************************
-* Example sketch for the ADS1115_WE library
-*
-* This sketch shows how to use the ADS1115 in continous mode.
-*
-* Further information can be found on:
-* https://wolles-elektronikkiste.de/ads1115
-*
-***************************************************************************/
-
-#include<ADS1115_WE.h>
-#include<Wire.h>
-#define I2C_ADDRESS 0x48
-
-ADS1115_WE adc(I2C_ADDRESS);
-// ADS1115_WE adc = ADS1115_WE(); // Alternative: uses default address 0x48
-
-void setup() {
- Wire.begin();
- Serial.begin(9600);
- if(!adc.init()){
- Serial.println("ADS1115 not connected!");
- }
-
- /* Set the voltage range of the ADC to adjust the gain
- * Please note that you must not apply more than VDD + 0.3V to the input pins!
- *
- * ADS1115_RANGE_6144 -> +/- 6144 mV
- * ADS1115_RANGE_4096 -> +/- 4096 mV
- * ADS1115_RANGE_2048 -> +/- 2048 mV (default)
- * ADS1115_RANGE_1024 -> +/- 1024 mV
- * ADS1115_RANGE_0512 -> +/- 512 mV
- * ADS1115_RANGE_0256 -> +/- 256 mV
- */
- adc.setVoltageRange_mV(ADS1115_RANGE_6144); //comment line/change parameter to change range
-
- /* Set the inputs to be compared
- *
- * ADS1115_COMP_0_1 -> compares 0 with 1 (default)
- * ADS1115_COMP_0_3 -> compares 0 with 3
- * ADS1115_COMP_1_3 -> compares 1 with 3
- * ADS1115_COMP_2_3 -> compares 2 with 3
- * ADS1115_COMP_0_GND -> compares 0 with GND
- * ADS1115_COMP_1_GND -> compares 1 with GND
- * ADS1115_COMP_2_GND -> compares 2 with GND
- * ADS1115_COMP_3_GND -> compares 3 with GND
- */
- adc.setCompareChannels(ADS1115_COMP_0_GND); //comment line/change parameter to change channel
-
- /* Set number of conversions after which the alert pin will be active
- * - or you can disable the alert
- *
- * ADS1115_ASSERT_AFTER_1 -> after 1 conversion
- * ADS1115_ASSERT_AFTER_2 -> after 2 conversions
- * ADS1115_ASSERT_AFTER_4 -> after 4 conversions
- * ADS1115_DISABLE_ALERT -> disable comparator / alert pin (default)
- */
- //adc.setAlertPinMode(ADS1115_ASSERT_AFTER_1); //uncomment if you want to change the default
-
- /* Set the conversion rate in SPS (samples per second)
- * Options should be self-explaining:
- *
- * ADS1115_8_SPS
- * ADS1115_16_SPS
- * ADS1115_32_SPS
- * ADS1115_64_SPS
- * ADS1115_128_SPS (default)
- * ADS1115_250_SPS
- * ADS1115_475_SPS
- * ADS1115_860_SPS
- */
- // adc.setConvRate(ADS1115_8_SPS); //uncomment if you want to change the default
-
- /* Set continous or single shot mode:
- *
- * ADS1115_CONTINOUS -> continous mode
- * ADS1115_SINGLE -> single shot mode (default)
- */
- adc.setMeasureMode(ADS1115_CONTINOUS); //comment line/change parameter to change mode
-
- /* Choose maximum limit or maxium and minimum alert limit (window)in Volt - alert pin will
- * be active when measured values are beyond the maximum limit or outside the window
- * Upper limit first: setAlertLimit_V(MODE, maximum, minimum)
- * In max limit mode the minimum value is the limit where the alert pin will be deactivated (if
- * not latched)
- *
- * ADS1115_MAX_LIMIT
- * ADS1115_WINDOW
- *
- */
- //adc.setAlertModeAndLimit_V(ADS1115_MAX_LIMIT, 3.0, 1.5); //uncomment if you want to change the default
-
- /* Enable or disable latch. If latch is enabled the alarm pin will be active until the
- * conversion register is read (getResult functions). If disabled the alarm pin will be
- * deactivated with next value within limits.
- *
- * ADS1115_LATCH_DISABLED (default)
- * ADS1115_LATCH_ENABLED
- */
- //adc.setAlertLatch(ADS1115_LATCH_ENABLED); //uncomment if you want to change the default
-
- /* Sets the alert pin polarity if active:
- *
- * Enable or disable latch. If latch is enabled the alarm pin will be active until the
- * conversion register is read (getResult functions). If disabled the alarm pin will be
- * deactivated with next value within limits.
- *
- * ADS1115_ACT_LOW -> active low (default)
- * ADS1115_ACT_HIGH -> active high
- */
- //adc.setAlertPol(ADS1115_ACT_LOW); //uncomment if you want to change the default
-
- /* With this function the alert pin will be active, when a conversion is ready.
- * In order to deactivate, use the setAlertLimit_V function
- */
- //adc.setAlertPinToConversionReady(); //uncomment if you want to change the default
-
- Serial.println("ADS1115 Example Sketch - Continous Mode");
- Serial.println();
-}
-
-void loop() {
- float voltage = 0.0;
- voltage = adc.getResult_V(); // alternative: getResult_mV for Millivolt
- Serial.print("Channel 0 vs GND [V]: ");
- Serial.println(voltage);
- Serial.println("-------------------------------");
- delay(2000);
-}
+/*************************************************************************** +* Example sketch for the ADS1115_WE library +* +* This sketch shows how to use the ADS1115 in continuous mode. +* +* Further information can be found on: +* https://wolles-elektronikkiste.de/ads1115 +* +***************************************************************************/ + +#include<ADS1115_WE.h> +#include<Wire.h> +#define I2C_ADDRESS 0x48 + +ADS1115_WE adc(I2C_ADDRESS); +// ADS1115_WE adc = ADS1115_WE(); // Alternative: uses default address 0x48 + +void setup() { + Wire.begin(); + Serial.begin(9600); + if(!adc.init()){ + Serial.println("ADS1115 not connected!"); + } + + /* Set the voltage range of the ADC to adjust the gain + * Please note that you must not apply more than VDD + 0.3V to the input pins! + * + * ADS1115_RANGE_6144 -> +/- 6144 mV + * ADS1115_RANGE_4096 -> +/- 4096 mV + * ADS1115_RANGE_2048 -> +/- 2048 mV (default) + * ADS1115_RANGE_1024 -> +/- 1024 mV + * ADS1115_RANGE_0512 -> +/- 512 mV + * ADS1115_RANGE_0256 -> +/- 256 mV + */ + adc.setVoltageRange_mV(ADS1115_RANGE_6144); //comment line/change parameter to change range + + /* Set the inputs to be compared + * + * ADS1115_COMP_0_1 -> compares 0 with 1 (default) + * ADS1115_COMP_0_3 -> compares 0 with 3 + * ADS1115_COMP_1_3 -> compares 1 with 3 + * ADS1115_COMP_2_3 -> compares 2 with 3 + * ADS1115_COMP_0_GND -> compares 0 with GND + * ADS1115_COMP_1_GND -> compares 1 with GND + * ADS1115_COMP_2_GND -> compares 2 with GND + * ADS1115_COMP_3_GND -> compares 3 with GND + */ + adc.setCompareChannels(ADS1115_COMP_0_GND); //comment line/change parameter to change channel + + /* Set number of conversions after which the alert pin will be active + * - or you can disable the alert + * + * ADS1115_ASSERT_AFTER_1 -> after 1 conversion + * ADS1115_ASSERT_AFTER_2 -> after 2 conversions + * ADS1115_ASSERT_AFTER_4 -> after 4 conversions + * ADS1115_DISABLE_ALERT -> disable comparator / alert pin (default) + */ + //adc.setAlertPinMode(ADS1115_ASSERT_AFTER_1); //uncomment if you want to change the default + + /* Set the conversion rate in SPS (samples per second) + * Options should be self-explaining: + * + * ADS1115_8_SPS + * ADS1115_16_SPS + * ADS1115_32_SPS + * ADS1115_64_SPS + * ADS1115_128_SPS (default) + * ADS1115_250_SPS + * ADS1115_475_SPS + * ADS1115_860_SPS + */ + // adc.setConvRate(ADS1115_8_SPS); //uncomment if you want to change the default + + /* Set continuous or single shot mode: + * + * ADS1115_CONTINUOUS -> continuous mode + * ADS1115_SINGLE -> single shot mode (default) + */ + adc.setMeasureMode(ADS1115_CONTINUOUS); //comment line/change parameter to change mode + + /* Choose maximum limit or maximum and minimum alert limit (window)in Volt - alert pin will + * be active when measured values are beyond the maximum limit or outside the window + * Upper limit first: setAlertLimit_V(MODE, maximum, minimum) + * In max limit mode the minimum value is the limit where the alert pin will be deactivated (if + * not latched) + * + * ADS1115_MAX_LIMIT + * ADS1115_WINDOW + * + */ + //adc.setAlertModeAndLimit_V(ADS1115_MAX_LIMIT, 3.0, 1.5); //uncomment if you want to change the default + + /* Enable or disable latch. If latch is enabled the alarm pin will be active until the + * conversion register is read (getResult functions). If disabled the alarm pin will be + * deactivated with next value within limits. + * + * ADS1115_LATCH_DISABLED (default) + * ADS1115_LATCH_ENABLED + */ + //adc.setAlertLatch(ADS1115_LATCH_ENABLED); //uncomment if you want to change the default + + /* Sets the alert pin polarity if active: + * + * Enable or disable latch. If latch is enabled the alarm pin will be active until the + * conversion register is read (getResult functions). If disabled the alarm pin will be + * deactivated with next value within limits. + * + * ADS1115_ACT_LOW -> active low (default) + * ADS1115_ACT_HIGH -> active high + */ + //adc.setAlertPol(ADS1115_ACT_LOW); //uncomment if you want to change the default + + /* With this function the alert pin will be active, when a conversion is ready. + * In order to deactivate, use the setAlertLimit_V function + */ + //adc.setAlertPinToConversionReady(); //uncomment if you want to change the default + + Serial.println("ADS1115 Example Sketch - Continuous Mode"); + Serial.println(); +} + +void loop() { + float voltage = 0.0; + voltage = adc.getResult_V(); // alternative: getResult_mV for Millivolt + Serial.print("Channel 0 vs GND [V]: "); + Serial.println(voltage); + Serial.println("-------------------------------"); + delay(2000); +} |